Categories

Raspberry Pi 2m Band,Transmitter with two Low pass filters. (rpitx) 32.7mW (15.1dBm) Kit

Raspberry Pi 2m Band,Transmitter with two Low pass filters. (rpitx) 32.7mW  (15.1dBm) Kit
Raspberry Pi 2m Band,Transmitter with two Low pass filters. (rpitx) 32.7mW  (15.1dBm) Kit Raspberry Pi 2m Band,Transmitter with two Low pass filters. (rpitx) 32.7mW  (15.1dBm) Kit Raspberry Pi 2m Band,Transmitter with two Low pass filters. (rpitx) 32.7mW  (15.1dBm) Kit
Brand: Giga
Product Code: RPITX2MFBHAT
Availability: Out Of Stock
Price: R278.00
Ex Tax: R278.00
Qty:     - OR -   Add to Wish List
Add to Compare

Raspberry, Pi, 2m, band, Transmitter, Low, pass, filters, rpitx, estimated Power, 32.7mW  ,15.1dBm (KIT)

  • There is a very nice library that will run on Raspberry Pi one B called rpitx witch can generate CW,SSB,FM SSTV...
  • ​Here is a image of a assembled Ceramic filter below, (this board is only avalible with ​Ceramic filter components in kit format.)
  • This board allows you select one of two filter. (2 x SMA connectors one for each filter).
  • The first filter is a seremic 2m low passfilter.
  • The second filter can be build with band selectable componenets for a 7 stage low pass filter for the band you requer.
  • The Table below has teh calculated Vules for the componenets for the difren HF bands. (6m to 80m)
  • The 2m seremic Low pass filter is componenet F1.
  • R10,R11,R12 could be used as a impedance matching circuit or an attenuator. As I did not know what the expected output impedance would be of the Digital pin you can now match the impedance. (I use open shunt and 0 ohm in line for now until impedance can be measured.)
  • The 7 stage low pass filter componenets consist of the followoing. (C4,C5,C6 and inductors L1,L2,L3,L4.
  • I also added a input and output resistor matching circuit for the 7 stage low pass filter to match impedanses.
  • The matching componenets for input is R2,R3,R5 and for output is R6,R7,R8. (I use open shunt and 0 ohm in line for now until impedance can be measured.)You could use it as atenuator if the signal is to big.
  • I have added a PTT surcuite so that you can controle a PTT of  a power Amp stage witch consits of R1, Q1, R4 with LED indicater.
  • The PTT can be controlled with a digital pin on Raspberry Pi. ( I Do have a 2W external power amp Board available in build format)
  • I also have added a low dropout 5V regulator so that you could power the board externaly without Raspberry pi from a battery. (U1 C2,C3)
  • Yous hould be able to do APRS, QPRS, WSPR, RTTY, AFSK .... with this board.
  • Modelation options is FM, AM ,SSB, SSTV.

Please note this is a kit with the Ceramic filter components for 2m meter only. Assembled kits will be avalible soon.

Link to my Blog describing how to use this board as a repeater with a dongle.

Rubber duck and Raspbeery Pi is not included.

​Circuit diagram for both filters.

Digarm

Componenet list.

The blue componenets is includidt in this kit

XSL spread shee avalible here

3D model of Board

 

 

Filter values caliculated in simulator. (SVCFilter)

HF Low pass filter values. Some values is not practical for the SMD footprints

Asembly Instructions. (manual prosess)

1) Start with all the Surface Mount components as the connectors and big components will get in the way of your heat gun.

2) Best way to assemble SM components is to place solder paste on the pads and then place the component on the solder past.

3) I use a hot air soldering iron to heat up the SM componenets with an low wind speed not to blow of the SM component.

4) When the Solder paste start melting remove the heat gun and the component should now be solderd.

5) I dont use SM components smaller than 0805 so that its still reasonably big to work with a tweezer.

6) Why SM componenets? Whet you are starting to work with componenets in the VHF and UHF and higer frequency band the convention throw hole componenets is starting to afect the design and your design needs to compensae for that.

7) Conventional components is also bulky therefore the boards are bigger. So to reduce the cost and amd make a predictable design SM components is preveriable.

Link to my Blog describing how to use this board as a repeater with a dongle

Write a review

Your Name:


Your Review: Note: HTML is not translated!

Rating: Bad           Good

Enter the code in the box below:



Powered By OpenCart
Giga Technology © 2024