Categories

SoftRock RXTX Ensemble Transceiver (SDR) (Assembled - build and tested) Band Group - 40m/30m/20m

SoftRock RXTX Ensemble Transceiver (SDR) (Assembled - build and tested) Band Group - 40m/30m/20m
Brand: Softrock
Product Code: SRrxtxEnsembleBuild
Availability: 1
Price: R2,858.00
Ex Tax: R2,858.00
Qty:     - OR -   Add to Wish List
Add to Compare

SoftRock RXTX Ensemble Transceiver Kit (SDR) (Assembled -build and tested) Band Group - 40m/30m/20m

 

The SoftRock RXTX Ensemble Transceiver Kit provides a 1 watt SDR transceiver that can be built for one of the following five band groups: 
 
  • 160m
  • 80m/40m
  • 40m/30m/20m
  • 30m/20m/17m
  • 15m/12m/10m

Components are included for all five options and can be assembled at the builders choice. The circuit board measures 5 inches by 2.5 inches. 

NOTE: This product is a kit. The product photo shows what it should look like once assembled. A sound card with stereo line-in connector for receive and stereo line-out connector for transmit and a computer running SDR software are required to operate this radio. 

Sound Card Requirements

If you do not have a Delta 44 or FA66 soundcard, this kit requires one and possibly two soundcards to handle RX/TX. If the kit is to be used for non-digital modes (e.g., CW, SSB, AM, FM), then in addition to the usual quality stereo sound card for I and Q in/out, a second soundcard (for microphone input and speaker/headphone output) is required. This second card can be of lesser quality, e.g., an inexpensive "dongle").

What band to Choose?  If you are not certain of which band option you wish to build, check out the discussion in this thread on the Yahoo Softrock40 reflector

Once you have decided on your band choice, you can select the band by clicking on the "Bands" tab at the top of any page on the Ensemble RXTX website.  This will customize these notes (and theid component values) for the selected band option.  The band selection will hold for the duration of your "session" on the website and while in the Ensemble RXTX portion.  Get in the habit of checking the header on each page to be sure your band selection is still in effect.

In each version, the radio has complete frequency agility within the "super-band" (thanks to the reliable Si570 programmable oscillator), limited only by the fixed/installed band-specific components. This means that, for example, with the 30/20/17m version, the user can operate all modes on all three of those ham bands, anywhere in those bands, subject only to the limitations of their license and the SDR software being used. In fact, the kit can also receive any HF signals within the installed "super-band".

The kit provides an Atmel AVRMicrocontroller on-board, programmed to act as a USB device and installed in a galvanically isolated section of the board. Achange from the earlier transceivers is the addition of jumpers on board to switch the ring and tip assignments of RX and TX I and Q signals.

Another welcome change from the earlier models is that all connections to the outside world are handled via on-board jacks (provided with the kit).

The kit is offered with all of the parts necessary to build it for any one of the five possible versions. Consequently, the builder will always have some parts "left-over" at the end of the build. These documents contain band-specific Bill of Materials listings for each version (in addition to the Bill of Materials for the parts of the radio that are not band-specific.

Theory of Operation

Refer to the block diagram below

(click on any block in the diagram to go to the build stage which implements that block)

Foundation Circuitry

The transceiver is controlled by an Attiny85 microcontroller, programmed as a USB device to provide PTT control, paddles input, and local oscillator frequency control, in a galvanically isolated area of the PCB.

Power (+5 Vdc) for this section is provided by the USB bus from the PC. Power for the programmable local oscillator is provided by converting the USB bus power down to 3.3 Vdc (in the USB Power stage).

The function of the local oscillator is to produce a signal whose frequency is four times the desired "center frequency" of the radio. The "center frequency", plus the sound card in the PC, will determine the width of the "chunk of spectrum" one will see in the RX (and TX) display on the PC's screen - i.e., the available, visible bandwidth. This bandwidth is represented as a number of kHz either side of the "center frequency. That number of kHz is half of the sound card's sampling rate. Normal sampling rates are 48 kHz, 96 kHz, and 192 kHz (corresponding to bandwidths of the "center frequency" plus or minus 24 kHz, 48 kHz, and 96 kHz, respectively. The sampling rate of the sound card is directly proportional to the cost of the sound card - the higher the rate, the higher the cost.

The output of the local oscillator is fed to the dividers stage, where the signal is divided by 4, yielding two signals which are identical except that they are 90 degrees out of phase with each other - i.e., in quadrature. These signals are at the "center frequency" and will clock both the RX mixer and the TX mixer.

RX Circuitry

The transceiver has a common antenna terminal and RF path which is switched between the RX Bandpass filters (default) and the TX low-pass filters, via circuitry in the RF I/O and Switching Stage. The switching is performed in response to the /PTT signal from the microcontroller, as selected by the SDR program on the PC. In the RX chain, the incoming RF is band-pass filtered in T5/L4/C39, with the RF output at T5's secondaries in antiphase.

The antiphase RF signals out of T5 are coupled into the RX Mixer Stage via R53 and R54. The mixer chip (actually a commutating switch, clocked by the two QSD Clock signals from the Dividers Stage) outputs the product and difference signals of the incoming RF against the QSD clock. The effect is to down-convert the incoming RF into its quadrature analogues at frequencies ranging from 0 to roughly 100 kHz.

These quadrature pairs from the RX Mixer, identifcal in all respects except phase, are fed to the RX OpAmp Stage for amplification and filtering into the audio and infra-audio range and delivered to the RX output stereo audio jack, J4, to be input to the PC's STEREO input (line-in or Mic).

The PC's sound card performs a conversion of the two analog signals ("I and Q") to a digital representation, which is then operated upon by modules of the SDR program to perform the many "radio" functions, such as demodulation, filtering, AGC, etc., that are expected of a fine receiver. To do this, it absolutely essential that the soundcard being used supports STEREO input. The sampling rate, quality and specs of the soundcard will determine whether and how well the PC can work signals whose frequency is either sode of the center frequency. Common sound card sampling ratesfor this bandwidth are 48 kHZ, 96 kHz, and 192 kHz. These each correspond to the ability to support SDR processing of "chunks" of bandwidth of 48 kHz, 96 kHz, and 192 kHz, each chunk centered on the center frequency (CF), with "wings" on either side of the CF that are one-half the sampling rate in width.

TX Circuitry

The transmit functionality is essentially the reverse of the RX functionality. In the PC, rather than demodulating input I and Q signals as in the RX, the PC modulates the digital signals (from the microphone or a keyer module. for example) into analog I and Q (infra) audio STEREO outputs, typically output to the line-out jack on the soundcard. The I and Q signals at the line-out are in quadrature (identical in all respects save phase) and appear at stereo jack J3. There are fed to the TX OpAmp Stage. This unitary gain stage translates the I and Q signals into four equal signals, at 0, 90, 180, and 270 degrees of phase.  Where the mode is AM or SSB, there is a requirement for a separate sound card to handle the microphone input to the PC.  This soundcard does not require much in the way of quality; a cheap dongle can suffice for this purpose. 

These four signals from the TX Opamp Stage are coupled via R25-R28 to the TX Mixer Stage. Just as the RX Mixers "mixed" incoming RF with the QSD clock (center frequency) signals to produce (infra)audio signals, the TX Mixer does the reverse, "mixing" modulated (infra) audio signals with the QSE RF clock signals to produce up-converted RF outputs that are analogues of the TX I and Q inputs. This modulated RF output of the TX Mixer (aka "Quadrature Sampling Exciter", or "QSE") is coupled via T2, C20, L1, and C21 to the Driver/PA stage.

The Driver/PA stage shapes and amplifies the modulated RF output from the TX Mixer stage and feeds the result to the antenna path as switched by the PTT switching circuitry. The switching circuitry activates the Driver/PA stage and forces a S12 line to high (approximately 12 Vdc), to permit switching an external amplifier. This stage will deliver approximately one watt of output into a 50 ohm load.

For an excellent, simple discussion of the Theory of SDR, see Tobias DH1TW's "do you truly understand the SDR concept?"

Project Schematic

(Resistor testpoints (hairpin, top, or left-hand lead), as physically installed on the board, are markeSchematic for Ensemble_RXTXd in the schematic with red dots)(You can review the individual schematic sheets: sheet1sheet 2sheet 3 )

Project Bill of Materials

The Ensemble RXTX kit has an extensive Bill of Materials. The kit contains sufficient parts to build any one of the several band-coverage options. To aid the builder throughout the build, the bill of materials will be presented in several different ways:

  • Traditional Project Level Bill of Materials - for selected band (click to view)
  • Project Level Inventory of Components (regardless of selected band) (click to view)
  • Project Level Bill of Materials Cross-Referenced to Stages - for selected band (click to view)
  • In addition, each stage will show its own Bill of Materials for the selected band and
  • Each step, within a stage, will show its own Bill of Materials for the selected band

Board Layouts

Topside

topside layout

Underside

undersideside layout 
(Component colors: BLUE = band-specific; WHITE caps = 0.1 uF SMT - black striped strip; YELLOW caps = 0.01 uF SMT - clear strip)

Expert's (Terse) Build Notes

  1. Review the schematics sheets: ( sheet1sheet 2sheet 3))
  2. Install Power Supplies (12, 5, and 3.3 Vdc)
  3. Install Local Oscillator and Dividers
  4. Install RF Chain and Switching Circuitry
  5. Install RX: QSD amd OpAmps
  6. Install TX: Opamps and QSE
  7. Install Driver/PA
  8. Install Software and hookup RXTX

Ensemble RXTX Detailed Build Notes

For the non-expert builders among us, this site takes you through a stage-by-stage build of the kit. Each stage is self-contained and outlines the steps to build and test the stage. This ensures that you will have a much better chance of success once you reach the last step, since you will have successfully built and tested each preceding stage before moving on to the next stage.

Each stage is listed below, in build order, and you can link to it by clicking on its name below (or in the header and/or footer of each web page).

For kit building information, please see: WB5RVZ

 

Windows SDR# software is avalible here



Linux Quisk software.

Quisk is available here


 

Write a review

Your Name:


Your Review: Note: HTML is not translated!

Rating: Bad           Good

Enter the code in the box below:



Powered By OpenCart
Giga Technology © 2024