Categories

0.1 to 500MHz AD831 Mixer module with low distortion

0.1 to 500MHz AD831 Mixer module with low distortion
0.1 to 500MHz AD831 Mixer module with low distortion 0.1 to 500MHz AD831 Mixer module with low distortion
Brand: Giga
Product Code: AD83101TO500MHZMIX
Availability: 1
Price: R499.00
Ex Tax: R499.00
Qty:     - OR -   Add to Wish List
Add to Compare

0.1 to 500MHz AD831 Mixer module with low distortion. )(Color of board could be difrent)

Description:

  • Power Supply: +5V DC
  • Module Size: 50mm*50mm

 
Product Description

  • The AD831 is a low distortion, wide dynamic range, monolithic mixer for use in such applications as RF to IF downconversion in HF and VHF receivers, the second mixer in DMR base stations,direct-to-baseband conversion, quadrature modulation and demodulation, and doppler shift detection in ultrasound imaging applications. The mixer includes an LO driver and a low noise output amplifier and provides both user-programmable power consumption and third order intercept point.
  • The AD831 provides a +24 dBm third order intercept point for –10 dBm LO power, thus improving system performance and reducing system cost compared to passive mixers, by eliminating the need for a high power LO driver and its attendant shielding and isolation problems.
  • The RF, IF, and LO ports may be dc or ac coupled when the mixer is operating from ±5 V supplies or ac coupled when operating from a single-supply of 9 V minimum. The mixer operates with RF and LO inputs as high as 500 MHz.
  • The mixer’s IF output is available as either a differential current output or a single-ended voltage output. The differential output is from a pair of open collectors and  may be ac coupled via a transformer or capacitor to provide a 250 MHz output bandwidth. In downconversion applications, a single capacitor connected across these outputs implements a low-pass filter to reduce harmonics directly at the mixer core, simplifying output filtering. When building a quadrature-amplitude modulator or image reject mixer,  the differential current outputs of two AD831s may be summed by connecting them together.
  • An integral low noise amplifier provides a single-ended voltage output and can drive such low impedance loads as filters, 50 amplifier inputs, and A/D converters. Its small  signal bandwidth exceeds 200 MHz. A single resistor connected between pins OUT and FB sets its gain. The amplifier’s low dc offset allows its use in such direct-coupled applications as direct-to-baseband conversion and quadrature-amplitude demodulation.
  • The mixer’s SSB noise figure is 10.3 dB at 70 MHz using its output amplifier and optimum source impedance. Unlike passive mixers, the AD831 has no insertion loss and does not require an external diplexer or passive termination.
  • A programmable-bias feature allows the user to reduce power consumption, with a reduction in the 1 dB compression point and third-order intercept. This permits a tradeoff  between dynamic range and power consumption. For example, the AD831 may be used as a second mixer in cellular and two-way radio base stations at reduced power while still providing a substantial performance improvement over passive solutions.

Product Highlites:

  1. –10 dBm LO Drive for a +24 dBm Output Referred Third Order Intercept Point.
  2. Single-Ended Voltage Output
  3. High Port-to-Port Isolation
  4. No Insertion Loss
  5. Single- or Dual-Supply Operation
  6. 10.3 dB Noise Figure

Effect test chart:

One, 1MHZ and 2MHz mixing

Result

Two, 51MHz and 54MHz mixing

Result

Three, 99MHz and 100MHz mixing

Results

Spectrum analyzer test (output plus attenuation):

Input 50M+5M:

Input 100M+10M:

Input 150M+10M:

Input 200M+10M:

Input 300M+10M:

Write a review

Your Name:


Your Review: Note: HTML is not translated!

Rating: Bad           Good

Enter the code in the box below:



Powered By OpenCart
Giga Technology © 2024